Idec High Performance Series Manuel d'utilisateur télécharger pdf (Page 3)

WindO/I-NV2 User’s Manual Preface-2

SAFETY PRECAUTIONS

• Prevent the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F from falling while moving or transporting, otherwise

damage or malfunction of the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F will result.

• Use the product within the environmental limits given in the catalog and manual. Use of the product in high-

temperature or high-humidity environments, or in locations where it is exposed to condensation, corrosive gas

or large shock loads can create the risk of electrocution and fire.

• The HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F is designed for use in pollution degree 2. Use the HG2G-S/

-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F in environments of pollution degree 2. (based on the IEC60664-1 rating)

• Install the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F according to the instructions. Improper installation

will result in falling, failure, electrical shock, fire hazard, or malfunction of the HG2G-S/-5S/-5F, HG3G/4G, HG1F/

2F/2S/3F/4F.

• Prevent metal fragments or wire chips from dropping inside the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F

housing. Ingress of such fragments and chips may cause fire hazard, damage, and malfunction.

• Use a power supply of the rated value. Using a wrong power supply may cause fire hazard.

• The HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/3F/4F uses “PS2 of EN61131” as DC power supply. (based on the IEC/

EN61131 rating)

• Use wire of a proper size to meet the voltage and current requirements.

• When exporting the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/3F/4F to Europe, use an EN60127 (IEC60127)

approved fuse on the power line outside the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/3F/4F.

• The D-sub connector on the end of the cable of the HG2S is not water- and dust-proof. If protection against

water and dust is required, the user must implement a water-proof provision on the connector or replace the D-

sub connector with a water-proof connector.

• When exporting the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/3F/4F to Europe, use an EU-approved circuit protector.

• Make sure of safety before starting and stopping the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F. Incorrect

operation of the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F may cause mechanical damage or accidents.

• Use the HG2G-S/-5S/-5F, HG3G/4G, HG3F/4F in a local area network if you download, upload or monitor the

project data via the Ethernet port.

• The touch panel of the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F is made of glass, and will break if

exposed to excessive shock. Take due care when handling it.

• When more than one button is pressed at the same time, due to the detection characteristics of an analog type

touch panel, only the gravity center of the pressed area is sensed and the unit assumes that only one button is

pressed. Thus, when more than one button is pressed simultaneously, the resulting operation is not guaranteed.

• The screen becomes blank when the backlight is burnt out; however, the touch panel remains enabled. Incorrect

touch panel operation will occur when operating the touch panel when the backlight appears to be turned off

but is actually burnt out. Note that this erroneous operation may result in damage.

• Do not push hard or scratch the touch panel and protection sheet with a hard object such as a tool, because

they are damaged easily.

• At temperatures over the rated operating temperature, the clock accuracy is affected. Adjust the clock before use.

• For applications which require clock accuracy, adjust the clock periodically.

• Do not install the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F in areas subjected to strong ultraviolet rays,

since ultraviolet rays may impair the quality of the LCD.

• Do not attempt to disassemble, repair or modify the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F. This can

create the risk of fire or electrocution.

• When disposing of the HG2G-S/-5S/-5F, HG3G/4G, HG1F/2F/2S/3F/4F, do so as an industrial waste.

• Do not switch off the power or pull out the Memory Card while it is being accessed, as this may result in

destruction of the stored data. If the data on the Memory Card is corrupted, format the Memory Card.

• Be sure to confirm that the Memory Card Access lamp is not lit prior to turning the power off to the HG3G,

HG2F/3F/4F or pulling out the Memory card. Refer to this manual for details.

• Do not switch off the power or pull out the USB Flash Drive while it is being accessed, as this may result in

destruction of the stored data. If the data on the USB Flash Drive is corrupted, format the USB Flash Drive.

1 2 3 4 5 6 7 8 ... 143 144

Commentaires sur ces manuels

Pas de commentaire

Idec High Performance Series Manuel d'utilisateur Page 3

Commentaires sur ces manuels